Segway x2 SE Turf Bedienungsanleitung Seite 30
- Seite / 148
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
28
Segway PT Components and Subsystems (cont.)
The PT has been designed with concern for the safety of the rider and those who may be nearby. Redundant subsystems maintain controlled
operation of the PT in the unlikely event of a component failure. If one component in a subsystem fails, the other component continues to
operate, allowing you to come to a complete and safe stop before stepping off. The PT has five redundant subsystems: Controller Boards,
Motors, Batteries, the Balance Sensor Assembly, and LeanSteer Sensors.
LeanSteer Frame/Handlebar
Ensure the following:
• The Handlebar is attached to the LeanSteer Frame.
• The LeanSteer Frame is attached to the Powerbase.
• The Handlebar is adjusted to the appropriate height.
See "Attach the LeanSteer Frame" (p. 19) for detailed installation instructions.
The LeanSteer Frame pivots at the base to control left/right direction of the PT. If you lean to the left while holding the Handlebar, the LeanSteer
Frame pivots and the PT turns left. If you lean to the right while holding the handlebar, the LeanSteer Frame pivots and the PT turns right.
Always lean left or right in coordination with the LeanSteer Frame.
Tire/Wheel Assembly and Fenders
Ensure that Tires are inflated to the proper tire inflation pressure as specified in "Segway PT Specifications" (p. 12).
Tires and Wheels are shipped as an assembly. Do not remove the Tire from the Wheel.
The Fenders on the PT are designed to protect the rider from debris and to safeguard the rider while leaning into turns.
WARNING
Do not remove fenders or ride a Segway PT that has its fenders removed. Doing so could result in loss of control and/or serious personal injury.
- User Manual 1
- Trademarks 4
- Contact Information 4
- Table of Contents 5
- Table of Contents (cont.) 6
- About This Manual 9
- The Risk of Injury 9
- Before You Begin 9
- Related User Materials 10
- Safety Messaging 10
- Introduction 11
- Serial number location 12
- Segway PT Model Descriptions 13
- Segway PT Specifications 14
- Operating Limits 16
- Minimum Rider Weight 17
- Handlebar Cargo 17
- Maximizing Range 18
- Setting Up Your Segway PT 19
- Prepare the LeanSteer Frame 20
- Attach the LeanSteer Frame 21
- Adjust the Handlebar Height 23
- Install the Batteries 24
- Charge the Batteries 25
- The Segway PT 27
- LeanSteer Frame/Handlebar 30
- Powerbase 31
- Rider Detect Sensors 35
- Controller Boards 36
- Figure 20: Motor Location 37
- Balance Sensor Assembly 38
- Running Lights 39
- Batteries 40
- The InfoKey Controller 41
- InfoKey Controller (cont.) 42
- Beginner Button Functions 45
- Security Button Functions 49
- Information Display button 51
- Power/Standby button 51
- Safety Alerts 53
- Speed Limiter 54
- Stick Shake Warning 56
- Stick Shake Warning (cont.) 58
- Safety Shutdown 59
- Safety Shutdown (cont.) 60
- Empty Battery Condition 61
- Riding Your Segway PT 63
- Avoiding Hazards 64
- Avoiding Trips 65
- Avoiding Tips 65
- AvoidingTips(cont.) 66
- Figure 39: Powering On the PT 68
- Beginner button 69
- Turtle icon 69
- Step 4: Before Stepping On 70
- Step 5: Stepping On 71
- Step 5: Stepping On (cont.) 72
- Step 7: Stopping 74
- Step 8: Turning 75
- Step 9: Stepping Off 76
- Security button 77
- Practice Riding 79
- Practice Riding (cont.) 80
- Riding Etiquette 81
- Riding Etiquette (cont.) 82
- Report All Incidents 86
- Segway PT Batteries 87
- Battery Safety (cont.) 88
- Charging Your Batteries 89
- Charge Port 90
- Unplugging the Segway PT 91
- Charging Failures 91
- Regenerative Braking 92
- Replacing Batteries 96
- Shipping Li-ion Batteries 97
- Battery Disposal 97
- Maintaining Your Segway PT 99
- Maintaining Tires and Wheels 100
- Cleaning Your Segway PT 101
- Storing Your Segway PT 102
- Servicing Your Segway PT 103
- Parts Diagram 104
- TorqueSpecications 105
- Accessories 105
- Replacing Parts 105
- Service Procedures 106
- Remove the Handlebar 107
- Attach the Handlebar 107
- Service Procedures (cont.) 108
- Wheel Cap 111
- Wheel Nuts 113
- Tire/Wheel Assembly 113
- Gearbox Flange 113
- 8 mm fasteners 115
- Hub adapter nuts 115
- Hub adapter 115
- Dock the InfoKey Controller 119
- Undock the InfoKey Controller 119
- Troubleshooting the Segway PT 121
- Segway PT Will Not Power On 122
- Startup Error Conditions 129
- Balance Mode Error Conditions 130
- Reduced Performance Levels 131
- System Faults While Riding 132
- Pitch or Roll Angle Exceeded 133
- System Faults 134
- Contact and Legal Information 135
- Limited Warranty 136
- Radio Frequency Interference 136
- European Directives 137
- Other Standards 138
- Product Life and Recycling 140
- Patent Information 140
- Index (cont.) 142
- Tire Wear 145
- Your Segway PT 146
- 24010-00001 aa 148
Verwandte Produkte und Handbücher für Roller Segway x2 SE Turf
Roller Segway I Series Spezifikationen
(106 Seiten)
(106 Seiten)
Roller Segway I Series Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Roller Segway x2 Turf Spezifikationen
(13 Seiten)
(13 Seiten)
Roller Segway SE-3 Patroller Bedienungsanleitung
(92 Seiten)
(92 Seiten)
Roller Segway x2 Turf Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Roller Segway p Series Spezifikationen
(5 Seiten)
(5 Seiten)
Roller Segway GT Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Roller Segway XT Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Roller Segway x2 SE Bedienungsanleitung
(2 Seiten)
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.135 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern